Expert Answers about Toyota Land Cruiser

• How To Install a Timbren Axle-Less 5,200-lbs System on Aluminum Framed Travel Trailer
• You can absolutely use the Timbren Axle-Less Trailer Suspension System - 4" Lift Spindle w/ Brake Flange - 5,200 lbs # TASR5200S03 on your 2013 Livin Lite Camper with an aluminum frame, but you'll need to put some sort of buffer between the Timbren system and the frameto prevent galvanic corrosion. Your best bet is going to be putting a thin rubber pad between the steel mount and the aluminum I-beam. The powder coat on the steel should keep the two dissimilar metals from galvanic corrosion,...
  view full answer...


• Are Tow Hooks Removed When Installing Draw-Tite Hitch # 41015 On 1997 Toyota Land Cruiser
• You will not need to remove the spare tire when installing the Draw-Tite Class III 2 Inch Hitch # 41015 on your 1997 Toyota Land Cruiser. You will need to remove the tow hooks when you install the hitch, but you will reinstall the tow hooks on the vehicle. When you reinstall the tow hooks you will switch the location of the tow hooks. The passenger side tow hook will go on the drivers side and the drivers side tow hook will go on the passenger side. I am sending a link to the installation...
  view full answer...


• Install Instructions for Upgraded Circuit Protected Tail Light Converter Hardwire Kit
• The install instructions for the Upgraded Circuit Protected Tail Light Converter Hardwire Kit part # 119178KIT or part # 119178 are attached to this page for you. The instructions are the same for both models, the former simply comes with a circuit tester and connectors.
  view full answer...


• Does Bump Stop Inside Coil Spring Need to Be Removed When Installing Air Lift Suspension
• The bump stop needs to be removed when installing the Air Lift Suspension Air Springs, part # AL60728. I confirmed this with Air Lift.
  view full answer...


• Where Does a Brake Controller Plug Into on a 2014 Toyota Land Cruiser
• The factory brake controller harness on the 2014 Toyota Land Cruiser will be located underneath and left of the steering column, taped to another harness near the emergency brake pedal. It is possible that the harness is tucked up above the emergency brake pedal or behind the kick panel left of the pedal. If may only be present if the vehicle came with a factory 7-Way trailer connector. For a brake controller I recommend the P2, # 90885, because it is easy to set up and use and it is reliable....
  view full answer...


• Where To Mount Timbren Front Suspension Enhancement System # TTOFTUN4 on 2005 Toyota Land Cruiser
• The Timbren Front Suspension Enhancement System, part # TTOFTUN4, mounts where your factory bump stops are mounted. To install part # TTOFTUN4, you will have to remove the factory bump stops and replace with the Timbren System. To remove the factory bump stops, it may be a good idea to use penetrating oil if you have a hard time getting the bump stops loose. I have linked instructions for the Timbren Front Suspension Enhancement System, part # TTOFTUN4.
  view full answer...


• Does Air Valve Point Up or Down for Air Lift Air Bags on a 2003 Toyota Land Cruiser
• I checked with Air Lift and for air bags # AL60728 they say the air valve should be at the bottoms of the air bags when installed on your 2003 Toyota Land Cruiser.
  view full answer...


• Does the Autowbrake Require Re-Calibration When Power is Removed?
• Great News! The Autowbrake Electric Brake Controller part # 3430001 does not require a reset if it loses power. It is designed to store the settings until the next use of the trailer and will be at the same settings as when you disconnected. It is however very easy to change the settings on the controller if you switch vehicles or trailer loads. Check out the video my buddy Shane did on it to see some more details on the system.
  view full answer...


• How Do You Remove Thule WingBar Edge Crossbars From Edge Raised Rail Feet
• Ahhh, I see the issue here. What Jon said was correct, I think there was just a misunderstanding on what the actual issue was. We did not have much information on the removal of the Thule WingBar Edge Crossbars # TH89FE from the Edge Raised Rail Feet # TH69SC, so I went ahead and reached out to the manufacturer. I have included a picture that helps depict what I am talking about. Underneath the strip in the accessory slot, towards the end there is a small hole. This hole is where the...
  view full answer...


• Can the Wheel Trays Be Removed on the Yakima FourTimer 4 Bike Platform Rack
• Yes, the wheel trays can be slid off the Yakima HoldUp 4 Bike Platform Rack part # Y0443-2. However, this would not be able to be done with a bike attached as the bike would put downward pressure on the wheel tray which would then prevent them from sliding off with a bike sitting atop. The majority of bike racks will have removable wheel trays but more often than not, a thief is not going to think to remove them. When it comes down to it, there isn't a bike rack on the market that is...
  view full answer...


• Tips for Finding Brake Light Circuit of 1997 Toyota Land Cruiser for Brake Controller Install
• Since we don't have a way to let you know which of the wires on your brake pedal switch is the cold side we can only really help by offering a universal stoplight switch like the part # RM-751000 or a circuit tester with a hook end for probing wires like the # PTW2993 which makes testing hard to get to circuits much easier.
  view full answer...


• Location of Brake Controller Plug-In Port on 2006 Toyota Land Cruiser with Factory 7-Way Socket
• My technical contact at Tekonsha confirmed the two most probable locations for the brake controller port on your 2006 Toyota Land Cruiser with factory tow package. The most-likely spot is under the dash on an aluminum brace that supports the base of the steering column. The other place to check is behind the dash panel that holds the headlight switch. Once you locate the port you can use your extra wiring adapter # 3040-P to install the P3 controller part # 90195.
  view full answer...


• Location of Brake Controller Connector on 2007 Toyota Land Cruiser With Factory 7-Way Connector
• If your 2007 Toyota Land Cruiser has the factory 7-Way trailer connector, the brake controller connector will be located under the dash and left of the steering column. It will be taped to another wiring harness near the emergency brake pedal. There will be a 5-pin connector that mates with the one on the Tekonsha Wiring Adapter, part # 3040-P. It might also be tucked up behind some other wiring harnesses behind the drivers side kick panel. If that is the case you will need to remove...
  view full answer...


• Brake Controller Plug In Connector Location on a 2012 Toyota Land Cruiser
• On your 2012 Toyota Land Cruiser, if Toyota has kept the brake controller connector in the same location as the 2011 models, The harness is located underneath the dash, to the left of the steering column, taped to another harness near the emergency brake pedal. However it is possible that it could also be behind the kick panel in this same area.
  view full answer...


• Issues Installing Draw-Tite Trailer Hitch on 2002 Toyota Land Cruiser
• The Draw-Tite Max-Frame Trailer Hitch Receiver # 75095 referenced in your question is confirmed to fit your 2002 Toyota Land Cruiser. I spoke with my contact at Draw-Tite to see if they have heard of any particular installation issues with this model hitch on your Land Cruiser, and he stated they have not heard of anything on their end. Based on my research, it looks like the weld nut in question on the driver side (closest to the front of the vehicle) does not have a factory bolt in...
  view full answer...


• Troubleshooting Installation Of Draw-Tite Trailer Hitch Receiver Item # 75095
• The Draw-Tite Max Frame Trailer Hitch Receiver, Item # 75095, is a confirmed fit for your 1999 Toyota Land Cruiser so that is not the challenge. However, you need to install the sixth bolt because the security and stability of the Draw-Tite hitch and what it carries is dependent on all bolts being in place. I contacted the tech department of the manufacturer and they confirmed that that you must have all bolts in place. They recommended trying a thread tap and are confident this will...
  view full answer...


• How to Clean Weldnuts for Installing a Hitch on a 2006 Toyota Land Cruiser
• Dirty or corroded weldnuts can be an issue for hitch installs. What you will want to do is check out the help links I attached that detail how to clean them so that you can install that last bolt to secure your hitch. I can't safely recommend you only install 5 of the 6 required bolts to install the hitch part # 75095 that you referenced regardless of what you plan to tow.
  view full answer...


• How Would Redarc Tow Pro Elite Install in 2019 Toyota Land Cruiser
• To install the Tow Pro Elite brake controller part # RED44FR in your 2019 Toyota Land Cruiser you will need to start with a 4-way (if you do not have one). For that you would want the # C59496. From there you would need to convert the 4-way to a 7-way so that you can install the brake controller. For that you will want the Brake Controller Install Kit and 7-Way Adapter part # ETBC7. I attached installation instructions and an install video for this product as well.
  view full answer...


• Troubleshooting Blank Screen of Prodigy P3 Brake Controller
• Sounds like it has an internal problem and needs to be replaced. I wish there was a breaker to reset or fuse to replace but it sounds fried. You might try it again just to make sure the connectors are seating properly but otherwise it would be time for a new P3 part # 90195.
  view full answer...


• Can Thule WingBar Edge Legs Only Be Left on a 2021 Toyota Land Cruiser
• The Thule WingBar Edge system (parts linked below) that you have on your 2021 Toyota Land Cruiser is meant to come off of your roof as a complete system - there isn't a way to simply remove the crossbar part and leave the legs on. I'm attaching an installation video of this same type of setup on a 2015 Toyota 4Runner for you to see what I'm talking about. Really the only time you can leave part of the roof rack installed is if you have a Jeep or truck topper with specific fit kits that...
  view full answer...